imprint -
buy -
data protection
|
21.08.2024 FLAME "BLACK FILTERBANK" and "FM KOSMOS" New modules available soon!
|
29.04.2024 FLAME TON - MELODY LOOPER 60 SECOND JAMS 6-10 ... PREVIEW BY FX_BERG & SB24-REVIEW BY LES SONDIERS (french) |
03.03.2024 FLAME uMM MIDI-MERGER-THRU NEW MODULE AVAILABLE SOON The uMM combines a MIDI merger, two independent THRU distributors and a TRS-A/B converter in just a small 4HP module. All sockets on the module are in MIDI-TRS-B format. The basis of the MIDI merger with three inputs and three outputs is a small, powerful ARM processor with sufficient buffer memory. Up to three MIDI streams are mixed together on one output and can also be tapped via two additional outputs. Two LEDs signal how the merger works: one LED shows MIDI activity at the inputs and a second warns of too much data at the inputs. The second functional group consists of two independent, separate MIDI-THRU distributors. The MIDI data at the respective MIDI input can be picked up and distributed at the three underlying THRU outputs. If necessary, both units can be made into a 1-to-5 distributor by connecting an output from the left group to the input from the right group (stereo cable). The third functional group is a passive TRS-A to B converter. The TIP and RING pins on the stereo socket are swapped. For example, plug a stereo cable from a TRS-A output into the first jack and a stereo cable from a TRS-B input into the other jack. A MIDI-TRS-A can be connected to a MIDI-TRS-B module. This is also possible the other way around. MANUALS PDF MANUAL - Flame uMM (english) PDF HANDBUCH - Flame uMM (deutsch) |
05.02.2024 TAKT - Firmware update V1.4 (to fix the "Velocity record bug") DOWNLOAD: Firmware TAKT V1.4 (fixbug Velocity Record, LED update) |
05.02.2024 FLAME AIRLECTRON NEW MODULE AVAILABLE |
AIRLECTRON - DISTANCE CV RECORDER The AIRLECTRON is a small, compact CV module with a distance sensor and recording function. The module can record the CV generated by hand movement over the sensor up to a length of more than two minutes. The sequence remains stored in the battery-backed RAM even after switching off. There is a HOLD function to hold the CV at the current position above the sensor. Additionally, a GATE is set when the sensor is triggered. A START/RESET input is used to reset/start recording/playback. The voltage generated is available at two CV outputs, bipolar from approx. +/-5v and unipolar from approx. 0 to +10v. Both outputs have a passive attenuator so that the voltage range can be set lower. The RANGE control is used to set the distance range (up to approx. 40 cm) of the distance sensor. The sensor is independent of external light and provides a logarithmic voltage curve with 12-bit resolution. MANUALS PDF MANUAL - Flame AIRLECTRON (english) PDF HANDBUCH - Flame AIRLECTRON (deutsch) |
10.01.2024 FIRE - Firmware update V1.04 (to fix the "CV/Velocity bug" version 1.03) DOWNLOAD: Firmware FIRE V1.04 (fixBug V1.03) MANUALS: PDF MANUAL V1.03 - Flame FIRE (english) PDF HANDBUCH V1.03- Flame FIRE (deutsch) |
21.12.2023 NEW FIRE UPDATE V1.03 AVAILABLE |
WHAT's NEW! The FIRE update provides new algorithms, MIDI controller extensions and more functions for the USER-CV inputs. In addition, some bugs have been fixed. There are three other algorithms for sounds: - COW BELL (for creating metal-like sounds with frequency shifter) - xCLAP (for more experimental clap/noise sounds) - WAVETABLE (wavetable oscillator with modulation LFO, filter, pitch envelope etc.) USER CV extension: All controls from the Panorama, Volume and Morph menus can now be assigned to the two USER-CV inputs. You can now control a sound in panning via CV, for example. The USER-CV menu has been moved to the MASTER menu (press the PAGE key in the MASTER menu), previously it was in the MORPH menu! MIDI controller extension: The controls for the Panorama, Morph, Volume and Master pages can be controlled using MIDI ControlChange commands. The CC numbers are fixed, but differ in the assignment of the MIDI channel. All voices normally run on channel 10. However, if a voice is played tonally (all note numbers can be received), the MIDI channel belonging to the voice is automatically assigned. Download firmware/manuals here! (german/english) |
10.12.2023 TAKT TUTORIAL FROM SYNTHDAD INTRODUCTION, OVERVIEW, FUNCTIONS, SEQUENCING ... |
03.12.2023 FIRE TUTORIAL FROM SYNTHDAD INTRODUCTION, OVERVIEW, SOUND EDIT, EXAMPLES... |
30.11.2023 TAKT & FIRE 60 SECONDS JAMS 1-5 by FX_BERG |
20.11.2023 FLAME MINI CASE 56HP euro format case Available at Schneidersladen |
25.10.2023 TAKT - rhythm sequencer MANUALS: PDF USER GUIDE - Flame TAKT (english) PDF HANDBUCH- Flame TAKT (deutsch) |
26.08.2023 FIRE - 8 voice percussion synth TAKT - rhythm sequencer MANUALS: PDF MANUAL - Flame FIRE (english) PDF HANDBUCH- Flame FIRE (deutsch) PDF Quickstart - Flame TAKT (english) PDF Quickstart- Flame TAKT (deutsch) FIRMWARE Firmware FIRE V1.0 Firmware FIRE V1.02 Firmware TAKT V1.3 |
15.08.2023 FIRE - 8 voice drum percussion synth DEMO TRACKS ON SOUNDCLOUD |
15.05.2023 TAKT & TON & FIRE Sequencers (with distance sensor) and Drum synth INFORMATIONS: PDF - Flame TAKT (english) PDF - Flame TON (english) PDF - Flame FIRE (english) SONICSTATE VID YOUTUBE: |
31.05.2022 NOW AVAILABLE |
FLAME "+MIRROR" Dual Unipolarinverter module The module is an inverter for exclusively positive voltages. It inverts an applied positive voltage so that the maximum value becomes zero and zero becomes the maximum value. The input voltage is therefore not inverted into the negative voltage range (mirror axis 0v), but reflects a positive voltage around an adjustable axis within a fixed positive voltage range from 0v. There are 10 ranges, adjustable in 1V steps. The mirror axis is always on half of the set range. Negative voltages cannot be inverted with this module. Applied negative voltages are limited to approximately zero volts. The module has two identical function groups. Applications are, for example, the inversion within positive voltage ranges, GATE inversions (0/+5v to +5v/0v), or opposing melody lines (in connection with a connected quantizer). Download manuals here! (german/english) |
19.04.2022 C-1U KNOBREKORDER - Knob & CV recorder |
The C-1U module is a one-channel module for recording and playing back movements of controller. Those can be recorded with channel s knob. The movements will be output as control voltage. The record time amounts to one minute maximal. The track can be played once only (one shot) or in loop. The speed of the play back or the output offset is controllable with the pot. There are an additional CV input for CV recordings and a reset input. Track data remains permanently stored when a 3V battery is used to buffer the RAM. When the module is switched on, the recorded data is available again. The module can be operated unipolar or bipolar (set by jumper on the back). The module size is 12HP in 1U format (intellijel). Availability soon (may 2022). Download manuals here! (german/english) |
06.05.2021 NEW ANALOG VOCODER |
FLAME "VOCORDER" - Analog-Spectral-Looper The Flame "Vocorder" module is a compact combination of an analog vocoder and a digital CV recorder (looper). The centerpiece is an 8-channel analog vocoder with a total of 16 analog bandpass filters for analysis and synthesis. The analog generated analysis envelope CVs are digitized and output via the DA converter to the analog VCAs of the synthesis tapes. With the help of the record function, the envelope CVs of the analysis channels can also be recorded digitally and played back in the loop. You can manipulate the playback in different ways: swap filter channels on the fly (rerouting), change speed and playback direction etc. The module can also be a "normal classic vocoder": the envelopes are then always looped through via AD / DA conversion (direct vocoding) and can of course also be recorded. The analysis unit is ineffective during playback because the envelopes are played back from the memory. The current version is very compact, the module is only 12HP wide - see photo. There are two audio inputs for analysis (voices, drum etc) and synthesis (instruments). A monophonic digital oscillator with three waveforms and an analog noise generator are available for internal synthesis. There is also an unvoiced / voiced switch (controls the highpass with noise when there is sibilance). A respective mix controller is responsible for both synthesis sources. The VCO has a 1V / oct input and an additional direct audio output. The synthesis filters have audio outputs for odd / mono and even (mix of even / odd channels). The looper recorder has the following functions: buttons for record, start, stop. A triple toggle switch for the playback direction forwards, backwards, ping-pong, another for the type of triggering: Loop, OneShot, Gated. You can record about up to three minutes. The playback speed is adjustable (also via CV). The sampled loop is retained in the battery-backed memory even after switching off. In addition, there is a controller for rerouting the filter channel assignments from the analysis (or recorded channel) to the synthesis filters, also accessible via CV. A freeze function is also available. The filter / cutoff control regulates the synthesis bands manually with a combined lowpass-bandpass-highpass algorithm, so the synthesis filters can also be used as simple audio filters. Current (power consumption): maximum +12V: 220mA / -12V: 190mA Vocorder Sound example Download Quickstart Manual here! (english) Download Quickstart Handbuch hier! (deutsch) |
15.07.2020 NEW VID FLAME M ANDER 2.0 MIDI FUNCTIONS FROM THE TUESDAY NIGHT MACHINES! THANK YOU VERY MUCH! |
|
14.07.2020 NEW VID FLAME M ANDER 2.0 WORKFLOW FROM THE TUESDAY NIGHT MACHINES! THANK YOU VERY MUCH! |
|
01.07.2020 NEW VID FLAME QSLIDER IN ACTION! THANK YOU VERY MUCH TO ALEX4! |
|
20.05.2020 NEW FLAME M ANDER TUTORIAL FROM THE TUESDAY NIGHT MACHINES! THANK YOU VERY MUCH! |
|
|
|
|
25.02.2020 NEW 5HP MIDI MODULES |
FLAME " MCLK" MIDI-Analog-Clock-Divider FLAME " 16MCC" MIDI control change to 16 CV FLAME " QMCV" Quad MIDI-to-CV interface FLAME " MGTV" MIDI Gate/Velocity/Divider interface more informations here ... |
03.01.2020 NEW VID FLAME MIXER RECORDER FROM FELIX BERGLEITER! THANK YOU VERY MUCH! |
|
05.10.2019 NEW VID FROM ANALOGOWADUSZA ABOUT FLAME AUTOMIX! THANK YOU VERY MUCH! |
|
09.09.2019 NEW VID FROM ROBOTOPSY ABOUT FLAME CURVES! THANK YOU VERY MUCH! |
|
|
29.06.2019 NEW MANUALS "C3 MK2 KNOBREKORDER" and "JOYSTICK REKORDER" modules PDF - MANUAL C3-MK2 KNOBREKORDER module version 1.00 (english) PDF - HANDBUCH C3-MK2 KNOBREKORDER module version 1.00 (deutsch) PDF - MANUAL JOYSTICK REKORDER module version 1.00 (english) PDF - HANDBUCH JOYSTICK REKORDER module version 1.00 (deutsch) |
20.06.2019 FLAME "M ANDER" MANUALS Full manual (english, deutsch) and Quickstart manuals available! == More informations and downloads here == |
|
|
17.01.2019 COMING SOON: SYNTHESIZER "M ANDER" 4-voice synthesizer with dynamic controllable analog 12 channel filter bank including live sequencer with 12 filter channel tracks and polyphonic note track wavetable sound synthesis, compatible with 4VOX wavetables individual filter/amp envelopes, morphing filter types full midi-usb functions... and more metal case 300x195x60mm release date: may 2019 SOUND EXAMPLES (mp3) All sounds and sequences come exclusively from the M ANDER. No effects and drum machines were used. M ANDER EXAMPLE 1 M ANDER EXAMPLE 2 M ANDER EXAMPLE 3 M ANDER EXAMPLE 4 M ANDER EXAMPLE 5 M ANDER EXAMPLE 6 M ANDER EXAMPLE 7 M ANDER EXAMPLE 8 M ANDER EXAMPLE 9 M ANDER EXAMPLE 10 M ANDER EXAMPLE 11 M ANDER EXAMPLE 12 |
12.11.2018 FLAME "CURVES" MIDI UPDATE VERSION 2 New firmware version 2 is available now! More MIDI controller functions New "MAX FOR LIVE" patch available == More informations and downloads here == |
21.08.2018 FLAME "ARPEGGIATOR 2013" UPDATE VERSION 1.09 New firmware version 1.09.03 is available now! More functions / New manual == More informations and downloads here == |